ZIPSET PRINTING INKS MSDS

Material Safety Data Sheet For Zipset Printing Ink
Date: 8/15/95
For Printing Ink and Related Materials. Information on this form is propriety information and furnished solely for the use of our customers.

HAZARD RATINGS HAZARD GUIDELINES

HEALTH 1 0 MINIMAL

FLAMMABILITY 1 1 SLIGHT

REACTIVITY 0 2 MODERATE

PERSONAL PROTECTION B 3 SERIOUS

B NON-PHOTOCHEMICAL REACTIVE

1. PRODUCT IDENTIFICATION

Manufacturer's Name: Tokyo Printing Ink Mfg. Co., Ltd.

Address: 2-7-15 Tabatashinmachi, Kita-Ku Tokyo, Japan

Telephone No.: 011-81-3-3810-9700

Emergency U.S.A. Telephone No.: 1-800-365-8742

Product Class: OFFSET PRINTING INK

Trade Name: ZIPSET

2. HAZARDOUS INGREDIENTS

INGREDIENT
HAZARD DATA CAS #

Organic Pigments OSHA PEL 5MG/m3

Modified Rosin Ester 68082-96-2

(OIL MISTS)

Modified Rosin Ester 65997-11-7

Linseed Oil 8001-20-5

Maganese Octoate 15956-58-8

Cobalt Octoate 136-52-7

Petroleum Distillate 8042-47-5

Chemicals Listed as Carcinogen or Potential Carcinogen:

National Toxicology Program No

I.A.R.C. Monographs No

OSHA No

3. HEALTH EFFECT INFORMATION

Eye Contact: May cause burning and/or irritation.

Skin Contact: Repeated exposure may cause irritation

Inhalation: May cause headache, dizziness and/or nausea.

Ingestion: May cause mouth, esophagus and/or stomach irritation.

4. EMERGENCY AND FIRST AID PROCEDURES

Eye Contact: Flush eyes with large amounts of water while holding the eyelid open for approximately 15 minutes. SEEK MEDICAL ATTENTION.

Skin Contact: Remove contaminated clothing and wash skin with plenty of soap and water. Wash clothing before reuse. If irritation persists seek medical attention.

Inhalation: Remove victim to fresh air and restore breathing if necessary. SEEK MEDICAL ATTENTION and stay with victim until arrival of medical personnel.

Ingestion: Contact local poison control center or physician immediately. DO NOT induce vomiting.

5. PERSONAL HEALTH PROTECTION INFORMATION

Eye Protection: If splash potential exists, wear chemical splash goggles or face shield.

Skin Protection: Not required under normal usage. If product is used in abnormal ways, wear neoprene rubber gloves and apron or coveralls as needed to prevent repeated or prolonged skin contact.

Respiratory Protection: Not required under normal usage. If product is used in abnormal ways, wear OSHA approved respirator.

Ventilation: Adequate ventilation in accordance with good engineering practices.

Other: Wash hands and face with soap and water before eating or smoking.

6. FIRE PROTECTION INFORMATION

Flash Point: Greater than 305 degrees Fahrenheit.

Hazardous Decomposition: NONE

Extinguishing Media: Use NFPA Class B Extinguisher (Carbon Dioxide, Dry Chemical or Foam).

Special Fire Fighting Procedures: Water can be used to cool containers exposed to heat or fire.

Unusual Fire or Explosive Conditions: Dense smoke may be generated when burning.

Hazardous Combustion Products: Products or combustion-smoke, CO, CO2.

7. REACTIVITY DATA
Stability (thermal, light, etc.): Stable
Incompatibility: May react with strong oxidizing agents.
Hazardous Polymerization: Stable
Hazardous Decomposition Products: None

8. ENVIRONMENTAL PRECAUTIONS

Procedures: Collect large spills with shovel, dry sand and/or absorbent materials. Clean spill area with detergent solutions. Provide adequate ventilation during clean up.

Waste Disposal Method: Waste material should be dumped or buried in an approved industrial waste landfill. Disposal must comply with all federal and local regulations.

9. SPECIAL PRECAUTIONS

Handling & Storage: Store in sealed containers away from heat, open flame and oxidizing materials. Fire extinguishers must be kept readily available and personnel trained in proper use.

Precautionary Statement: Do not transfer to unmarked containers. Follow DOT Regulations during Transport.

10. PHYSICAL PROPERTIES

Boiling Point: 450-505 degrees Fahrenheit

Solubility: Insoluble in water

Melting Point: Greater than 220 degrees Fahrenheit

HEALTH	1	0	MINIMAL
FLAMMABILITY	1	1	SLIGHT
REACTIVITY	0	2	MODERATE
PERSONAL PROTECTION	B	3	SERIOUS
	B	NON-PHOTOCHEMICAL REACTIVE

Manufacturer's Name:	Tokyo Printing Ink Mfg. Co., Ltd.
Address:	2-7-15 Tabatashinmachi, Kita-Ku Tokyo, Japan
Telephone No.:	011-81-3-3810-9700
Emergency U.S.A. Telephone No.:	1-800-365-8742
Product Class:	OFFSET PRINTING INK
Trade Name:	ZIPSET

INGREDIENT HAZARD DATA		CAS #
Organic Pigments		OSHA PEL 5MG/m3
Modified Rosin Ester		68082-96-2
(OIL MISTS)
Modified Rosin Ester		65997-11-7
Linseed Oil		8001-20-5
Maganese Octoate		15956-58-8
Cobalt Octoate		136-52-7
Petroleum Distillate		8042-47-5
Chemicals Listed as Carcinogen or Potential Carcinogen:
	National Toxicology Program	No
	I.A.R.C. Monographs	No
	OSHA	No

Eye Contact:	May cause burning and/or irritation.
Skin Contact:	Repeated exposure may cause irritation
Inhalation:	May cause headache, dizziness and/or nausea.
Ingestion:	May cause mouth, esophagus and/or stomach irritation.

Eye Contact:	Flush eyes with large amounts of water while holding the eyelid open for approximately 15 minutes. SEEK MEDICAL ATTENTION.
Skin Contact:	Remove contaminated clothing and wash skin with plenty of soap and water. Wash clothing before reuse. If irritation persists seek medical attention.
Inhalation:	Remove victim to fresh air and restore breathing if necessary. SEEK MEDICAL ATTENTION and stay with victim until arrival of medical personnel.
Ingestion:	Contact local poison control center or physician immediately. DO NOT induce vomiting.

Eye Protection:	If splash potential exists, wear chemical splash goggles or face shield.
Skin Protection:	Not required under normal usage. If product is used in abnormal ways, wear neoprene rubber gloves and apron or coveralls as needed to prevent repeated or prolonged skin contact.
Respiratory Protection:	Not required under normal usage. If product is used in abnormal ways, wear OSHA approved respirator.
Ventilation:	Adequate ventilation in accordance with good engineering practices.
Other:	Wash hands and face with soap and water before eating or smoking.

Flash Point:	Greater than 305 degrees Fahrenheit.
Hazardous Decomposition:	NONE
Extinguishing Media:	Use NFPA Class B Extinguisher (Carbon Dioxide, Dry Chemical or Foam).
Special Fire Fighting Procedures:	Water can be used to cool containers exposed to heat or fire.
Unusual Fire or Explosive Conditions:	Dense smoke may be generated when burning.
Hazardous Combustion Products:	Products or combustion-smoke, CO, CO2.

Procedures:	Collect large spills with shovel, dry sand and/or absorbent materials. Clean spill area with detergent solutions. Provide adequate ventilation during clean up.
Waste Disposal Method:	Waste material should be dumped or buried in an approved industrial waste landfill. Disposal must comply with all federal and local regulations.

Handling & Storage:	Store in sealed containers away from heat, open flame and oxidizing materials. Fire extinguishers must be kept readily available and personnel trained in proper use.
Precautionary Statement:	Do not transfer to unmarked containers. Follow DOT Regulations during Transport.

Boiling Point:	450-505 degrees Fahrenheit
Solubility:	Insoluble in water
Melting Point:	Greater than 220 degrees Fahrenheit